SR01924ATLanding gear and brakes
Manufacture of Low Skid or High Skid Landing Gear.
FAA holder: Bell Helicopter Textron Inc.
FAA STC category
Landing gear and brakes STCs
Landing gear, brake, wheel, tire, skid, and undercarriage changes. This directory contains 568 selected records listed with status Current in the June 30, 2026 FAA DRS snapshot and links every entry to its source.
Showing 361–480 of 568Page 4 of 5
View record
SA2747SWLanding gear and brakes
Installation of lockable, full swivel tail wheel per Drawing FA7027H, dated 5/11/78, or later FAA approved revision.
FAA holder: Turbine Conversions Ltd
SA11045SCLanding gear and brakes
Modification of the nose wheel shimmy damper in accordance with Down Time Aviation, LLC, drawing number DTA-TBM700-3252 (sheets 1-7); sheets 1-3 and 5-6 Revision A; sheet 4 Revision B; and sheet 7 Revision IR, all dated 12/7/2010 or later FAA approved revision. The aircraft is to be maintained per the Modification Instructions and Instructions for Continued Airworthiness, Document Number 32-52-01, Revision IR, dated January, 2011, or later FAA accepted revision.
FAA holder: Down Time Aviation LLC
SR01697AT-DLanding gear and brakes
Replacement Low or High Skid Tubes and Lightweight Flotation Skid Tubes in accordance with Aeronautical Accessories, Inc. Drawing List Report AA-98007, Revision I, dated July 18, 2006, and installation per Report AA-98006, Revision D, dated March 31, 2003, or per Report AA-99024, Revision F, dated November 29, 2005, or later DAS approved revisions.
FAA holder: Bell Helicopter Textron Inc.
SR09330RCLanding gear and brakes
Installation of Replacement Low and High Skid Landing Gear Crosstubes in accordance with data listed on Aeronautical Accessories, INC. drawing list, Report No. AA-00004, Revision C, dated October 2, 2001 or later FAA approved drawing list revision.
FAA holder: Bell Helicopter Textron Inc.
SR09532RC-DLanding gear and brakes
Installation of reduced-weight skid tubes for high skid landing gear in accordance with Master Drawing List AA-07045 Rev. A dated October 2, 2008, or later FAA approved revision.
FAA holder: Bell Helicopter Textron Inc.
SA02867NYLanding gear and brakes
Installation of the Lord Corporation Nose Wheel Shimmy Damper Part Number SE-1088-1 in accordance with Lord Corporation Installation Drawing List Document No. SE-1088-IDL, Revision IR, dated 4/22/2008 or later FAA approved revisions.
FAA holder: Lord Corporation
SA02376AKLanding gear and brakes
Replacement of tricycle landing gear with conventional (tail-wheel) landing gear.
FAA holder: Stoots Aviation David S. Stoots
ST02321LALanding gear and brakes
Installation and Replacement of Brake Components.
FAA holder: NASCO Aircraft Brake Inc
SA1177SWLanding gear and brakes
Installation of revised main landing gear doors.
FAA holder: Airline Fueling Inc.
SA02373AKLanding gear and brakes
Installation of heavy duty landing gear.
FAA holder: Dakota Cub Aircraft, Inc.
SA02304AK-DLanding gear and brakes
Installation of Airglas P/N LH4000F main wheel skis and optional Burl's Aircraft P/N 3400-10-23 tail ski.
FAA holder: Airglas Inc.
ST03832ATLanding gear and brakes
Installation of Nose Landing Gear Viewport with relocation of the viewport from aft of cargo bulkhead to forward of the cargo bulkhead.
FAA holder: Federal Express Corp
SH1018CELanding gear and brakes
Install landing gear damper piston.
FAA holder: Kinzie Industries Inc.
SH1047CELanding gear and brakes
Install modified landing gear damper.
FAA holder: Kinzie Industries Inc.
ST02264LALanding gear and brakes
Installation and replacement of steel brake components.
FAA holder: NASCO Aircraft Brake Inc
SA836WELanding gear and brakes
Hydro-Aire Mark II anti-skid braking system to reduce required landing field length.
FAA holder: Alaska Airlines Inc
SA5-2Landing gear and brakes
Installation of conventional tail wheel type landing gear from Piper PA-20 in place of tricycle type.
FAA holder: Aircraft Innovations, LLC
SA538ALLanding gear and brakes
Installation of modified landing gear (PA-18 type) with main landing gear legs lengthened6 inches.
FAA holder: Aircraft Innovations, LLC
SA548ALLanding gear and brakes
Installation of Piper PA-18 type landing gear.
FAA holder: Aircraft Innovations, LLC
SA1644SOLanding gear and brakes
Installation of main landing gear down-lock indicator system.
FAA holder: Pemco Aeroplex Inc
SH5889NMLanding gear and brakes
Installation of landing gear skid tubes.
FAA holder: Heli-Support Inc.
SR10117LA-DLanding gear and brakes
Installation of landing gear skid tubes.
FAA holder: Heli-Support Inc.
SA03708ATLanding gear and brakes
Replacement of the Main Landing Gear Housing.
FAA holder: Aeronautical Design Service Pty Ltd The
SA02698NYLanding gear and brakes
Main Landing Gear Compression Block installation.
FAA holder: Thunder Bay Aviation Ltd
ST1001SOLanding gear and brakes
Installation of Federal Express Corp. brake mount flange.
FAA holder: JSF Aviation Services Inc.
SA02339AKLanding gear and brakes
Installation of main gear gravel deflectors, PN GDQ-100, on the main landing gear of the Quest Kodiak 100.
FAA holder: Aero Twin Inc
SA02344AKLanding gear and brakes
Manufacture and installation of nose gear tire scraper, on the nose landing gear of the Quest Kodiak 100.
FAA holder: Aero Twin Inc
SA00021MCLanding gear and brakes
Installation of Michelin Main Landing Gear Radial Tires, P/N M16301.
FAA holder: Michelin North America Inc.
SA1113NWLanding gear and brakes
Installation of Cleveland wheels, tires (6 X 6) and brake assembly.
FAA holder: Burl's Aircraft LLC
ST02159LALanding gear and brakes
Installation and replacement of Steel Brake Components.
FAA holder: NASCO Aircraft Brake Inc
SA2381NMLanding gear and brakes
Installation of Knots 2U, Ltd Wheel and Body Fairings.
FAA holder: Knots 2U Ltd.
SA02546NYLanding gear and brakes
Installation of the Lord Corporation Nose Wheel Shimmy Damper Part Number SE-1090-1.
FAA holder: Lord Corporation
SA8031NMLanding gear and brakes
Installation of locking tail wheel strut.
FAA holder: 195 FACTORY LLC, The
SA4546NMLanding gear and brakes
Installation of Cleveland Part No. 040-19900 Tail Wheel Assembly and 10 x 3.50 4 tire and tube. Installation.
FAA holder: 195 FACTORY LLC, The
ST02385NYLanding gear and brakes
De-activation of Tire Pressure Indication System.
FAA holder: Corporation Logic Air Inc.
SH1861SOLanding gear and brakes
Installation of external cargo rack and work platform between the skid gears.
FAA holder: Haverfield International
ST01294CHLanding gear and brakes
Installation of a parking brake control assembly.
FAA holder: AeroControlex Group Inc
ST01477WI-DLanding gear and brakes
Installation of the M45 Updated Nose Wheel Steering and Spoiler/Spoileron Computers.
FAA holder: Learjet Inc
SA4463NMLanding gear and brakes
Installation of Ryan Model ST-A type main landing gear.
FAA holder: Helicorp Inc.
SA4-1322Landing gear and brakes
Fire proofing of main landing gear doors to comply with Airworthiness Directive 60-05-02.
FAA holder: Flying Tiger Line Inc
SA00555DELanding gear and brakes
Replacement of inboard main landing gear door with an aerodynamic fairing.
FAA holder: Aircraft Restoration Corporation
ST02151NYLanding gear and brakes
Installation of Dunlop Aircraft Tyres Limited Main Landing Gear Tyre(s) P/N DR32118T and Nose Landing Gear Tyre(s) P/N DR32212T.
FAA holder: Wilkerson Co Inc
SA01033WILanding gear and brakes
Replacement of original outboard main landing gear doors with a one-piece monolithic machined metal door.
FAA holder: Machining Programming Manufacturing Inc
SA00902WILanding gear and brakes
Replacement of original main landing gear doors with monolithic machined gear doors.
FAA holder: MPM Inc.
SA573ALLanding gear and brakes
Install Cleveland wheel assembly 40-28 and Cleveland brake assembly30-18.
FAA holder: STOL Aviation LLC c/o Tom Csatari
SA574ALLanding gear and brakes
Installation of Cleveland 40-28, 6.00 - 6 main wheel assemblies and Cleveland 30-18 brake assemblies.
FAA holder: STOL Aviation LLC c/o Tom Csatari
ST02436NYLanding gear and brakes
Installation of Main Wheel Stowage.
FAA holder: Elisen Technologies Inc.
SA01516SELanding gear and brakes
Replacement of the Scott Master Brake Cylinder (Non-Vented Diamphram type) with a Steve s Aircraft Model SA6-01 Master Cylinder with a vented reservoir.
FAA holder: Steve's Aircraft
ST01000CHLanding gear and brakes
Installation of AlliedSignal Flight Data Recorder and new sensors; for control wheel & rudder pedal position as well as aileron, rudder and elevator surface position.
FAA holder: Canard Aerospace Corporation
ST01249NYLanding gear and brakes
Installation of Take-off Configuration Test Switch and Nose Landing Gear Pin Position Switch.
FAA holder: Aero Consulting Services Ltd
ST511CHLanding gear and brakes
Eliminate 27,000 landing cycle life limit of the landing gear by placing aircraft on an inspection program described by the Murray Aviation document titled CASA C212-200 Series Aircraft Landing Gear Continued Airworthiness Limitations , no revision, dated January 23, 1996, or later FAA Approved Revision.
FAA holder: Presidential Airways Inc
SH7054NMLanding gear and brakes
Installation of a skid toe mounted convex mirror for sling load operations.
FAA holder: Heli-Support Inc.
SA138SOLanding gear and brakes
D18S landing gear 404-188400 on C18S.
FAA holder: Staggerwing Museum Foundation Inc.
SA2-1230Landing gear and brakes
Installation of extended tail wheel assembly.
FAA holder: Staggerwing Museum Foundation Inc.
SA2-1261Landing gear and brakes
Install Fiberglas bubble tail wheel enclosure doors (enclosing entire wheel).
FAA holder: Staggerwing Museum Foundation Inc.
SA2-338Landing gear and brakes
Installation of two (2) 25,000 BTU Janitrol Heaters installed one (1) in each wheel well.
FAA holder: Staggerwing Museum Foundation Inc.
SA3-383Landing gear and brakes
Beech D18S Goodyear wheels and brake assembly.
FAA holder: Staggerwing Museum Foundation Inc.
SA31SOLanding gear and brakes
Tricycle landing gear and revised nose assembly with optional radome. (Model may also be designated as Conrad 10,200.).
FAA holder: Staggerwing Museum Foundation Inc.
SA4-128Landing gear and brakes
Engines, propellers, revised nacelles, wheel-well doors, air- speed system, fuel system and elevator seal strips.
FAA holder: Staggerwing Museum Foundation Inc.
SA4-152Landing gear and brakes
Two Model 940 Stewart-Warner heaters, install one in each wheel well.
FAA holder: Staggerwing Museum Foundation Inc.
SA00759NYLanding gear and brakes
Installation of Northeast Engineering landing gear actuator rod.
FAA holder: Northeast Engr & Dev Ltd
SA02137ATLanding gear and brakes
Installation of the Lord Corporation Nose Wheel Shimmy Damper P/N SE-1051.
FAA holder: Lord Corporation
SA02138ATLanding gear and brakes
Installation of Lord Corporation nose wheel shimmy damper part number SE-1051-2/3.
FAA holder: Lord Corporation
SR02116NY-DLanding gear and brakes
Installation of Nose Wheel Position Advisory System.
FAA holder: Petroleum Helicopters Inc
SA4-506Landing gear and brakes
Installation of Cessna T-50 tail wheel assembly.
FAA holder: Skyhaven Inc
SA02007AKLanding gear and brakes
Installation of main landing gear long step no. 3195.
FAA holder: F Atlee Dodge Aircraft Service
SA02269AKLanding gear and brakes
Installation of a 6.00-6 type III wheel and 6.00/7.00-6, 6-ply type III tire using a Cessna 310 nose fork and operated as a tail wheel on DHC-2 Series airplanes.
FAA holder: Tailwind Aviation Inc
SA111WELanding gear and brakes
Installed Volpar Mark IV tricycle landing gear.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA1171WELanding gear and brakes
Installation of two AiResearch TPE331 Series engines, tricycle landing gear, wing platform modifications, and related modifications.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA1832WELanding gear and brakes
Installation of Volpar Tricycle Landing Gear.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA2204WELanding gear and brakes
Installation of 2 AiResearch TPE331-1 series turbo prop engines with Hartzell HCB3TN propellers: 8-1/2 inches extension of fuselage and ventral fin, tricycle landing gear installation and related modifications.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA01657SELanding gear and brakes
Fabrication of Robair main landing gear lower support fairing .
FAA holder: Robair Repair
SA4-1397Landing gear and brakes
Installation of Tricycle landing gear and nose assembly.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA4-1531Landing gear and brakes
Installation of Tricycle landing gear and revised nose assembly with optional radome.
FAA holder: SOUTHWESTERN AERO EXCHANGE INC.
SA01063CHLanding gear and brakes
Installation of a Scott Model 3200 Tail Wheel with the AESI #T.S.05P Tail Spring.
FAA holder: Univair Aircraft Corporation
SA2318NMLanding gear and brakes
Fabrication of North River Aviation model 8400 brake booster assemblies, and modification of Scott Aviation model B-711 brake master cylinders by installation of said assemblies.
FAA holder: Northern Piper Aviation Inc.
SA3633NMLanding gear and brakes
Fabrication of North River Avia. Model 8400 brake booster assembly, and modify Scott Avia. Model B-711 brake master cylinders.
FAA holder: Northern Piper Aviation Inc.
SA3634NMLanding gear and brakes
Fabrication of North River Avia. Model 8400 brake booster assembly, and modifcation of Scott Aviation Model B-711 brake master cylinders.
FAA holder: Northern Piper Aviation Inc.
SA3635NMLanding gear and brakes
Fabrication of North River Model8400 brake booster assembly and modification of Scott Aviation Model B-711 brake master cylinders.
FAA holder: Northern Piper Aviation Inc.
SA4629NMLanding gear and brakes
Fabrication of Model 8400 brake booster assemblies, and modification of Scott Aviation Model B-711 brake master cylinders by installation of said assemblies.
FAA holder: Northern Piper Aviation Inc.
SA4653NMLanding gear and brakes
Fabrication of Model 8400 brake booster assembly, and modification of Scott Aviation Model B-711 brake master cylinder by installation of said assembly. (PA-22-108 SN 22-8000 thru 22-9848).
FAA holder: Northern Piper Aviation Inc.
SA7974SWLanding gear and brakes
Installation of wheel pant fairings.
FAA holder: Dallas Metroplex Aviation
ST01369WI-DLanding gear and brakes
Installation of the M45 Updated Nose Wheel Steering and Spoiler/Spoileron Computers.
FAA holder: Learjet Inc
SA945NELanding gear and brakes
Gross weight increase (6,000 lbs. when operated on wheels, wheel/skis and floats and 5950 lbs. when operatedon amphibious floats on land). (DHC-2 (L-20A) MK.III turbo Beaver).
FAA holder: Viking Air Limited
ST01619SELanding gear and brakes
Fabrication of Honeywell International, Inc. (Honeywell) wheel assembly part number 2615901-1, Revision C, dated June 7, 2005 or later Federal Aviation Administration (FAA) approved revision and/or brake assembly part number 2615902-1, Revision C, dated July 15, 2005 or later FAA approved revision.
FAA holder: Honeywell International Inc
ST01833LALanding gear and brakes
Installation of brake components.
FAA holder: NASCO Aircraft Brake Inc
ST03183ATLanding gear and brakes
Installs Goodyear Radial Tire size 1050x395R16, P/N 109Q89-1 on Airbus A330 and A340 Nose Landing Gear.
FAA holder: Goodyear Tire and Rubber Company
SH288NWLanding gear and brakes
Installation of Hiller landing gear float kit No. 44012. (UH-12E modified per STC SH178WE).
FAA holder: Siam Hiller Holdings Inc
SA03139ATLanding gear and brakes
Conversion of Cessna Models 182, 182A, 182B, 182C, and 182D from a Tricycle Landing Gear (nose wheel) to a Conventional Landing Gear (tail wheel) configuration.
FAA holder: Rawson Rod
SA290WELanding gear and brakes
Main landing gear doors.
FAA holder: Staggerwing Museum Foundation Inc.
ST02062CHLanding gear and brakes
Install Aircraft Braking Systems Corporation (ABSC) Nose Landing Gear Wheel Assembly 9550267-6A or 9550267-7A.
FAA holder: Aircraft Braking Systems Corporation
ST01567SELanding gear and brakes
Fabrication of Honeywell Aircraft Landing Systems (ALS) brake assembly part number 2615512-2 and/or wheel assembly part number 2615511-1.
FAA holder: Honeywell International Inc
SA02244AKLanding gear and brakes
Fabrication and installation of Airglas, Inc., Model LH4000 hydraulically retractable wheel skis.
FAA holder: Airglas Inc.
ST03099ATLanding gear and brakes
Installation of a Replacement Landing Gear Wiring Harness.
FAA holder: Chippewa Aerospace, Inc.
SH287NWLanding gear and brakes
Installation of Hiller landing gear float kit No. 44012. (UH-12d (ARMY UH-23D modified per STC SH177WE).
FAA holder: Siam Hiller Holdings Inc
ST02083NYLanding gear and brakes
Installation of structural reinforcements and landing gear placards.
FAA holder: Field Aviation East Limited
SA507CHLanding gear and brakes
Installation of Cleveland based hydraulic toe brake rudder pedal system.
FAA holder: Aero Fabricators Co
SA02236AKLanding gear and brakes
Fabrication and installation of F. Atlee Dodge Heavy Duty Standard Length Main Landing Gear, P/N 3225A, in accordance with F. Atlee Dodge Master Data List No. 3225-1.5, Revision: None dated March 14, 2005, or later FAA approved revisions.
FAA holder: F Atlee Dodge Aircraft Service
SR01430LALanding gear and brakes
Installation of Stainless Steel Skid shoes.
FAA holder: Papas Gary Los Angeles Laboratories Inc.
ST01595LA-DLanding gear and brakes
Installation of Control Wheel Lighted Chart Holders.
FAA holder: Learjet Inc.
SR01136SELanding gear and brakes
Fabrication of AMC AM369A6200-45, -46, -57, -58 Landing Gear Fillet Fairings and AM369H6200-73, and -74 Landing Gear Fairing Guides per AMC Master Drawing List No. MDL-AMC-003, Rev A, dated August 29, 2002 or later FAA approved revision; and installation of this assembly in accordance with the Maintenance Manual for the rotorcraft, document number CSP-HMI-2, Rev 21, or later FAA approved revision.
FAA holder: Aerometals
SR01204SELanding gear and brakes
Fabrication of AMC AMC369H92827 pin, clevis-rotor brake.
FAA holder: Aerometals
SA02234AKLanding gear and brakes
Installation of a high Pressure Brake Master Cylinder assembly DCA1248-1260.
FAA holder: Dakota Cub Aircraft Inc
SH7951SWLanding gear and brakes
Installation of the Kaflex rotor brake modification.
FAA holder: Kamatics Corporation
ST01273WI-DLanding gear and brakes
Installation of a Main Landing Gear Door Actuator Modification Kit on Learjet Model 45 aircraft in accordance with FAA Approved Master Drawing List M100451ICT, Revision B dated December 21, 2004, FAA approved January 4, 2005, or later FAA Approved Revision.
FAA holder: Learjet Inc
ST02037CHLanding gear and brakes
Installation of Michelin main landing gear tires.
FAA holder: World Harvest Church
SA3987WELanding gear and brakes
Increase in takeoff gross weight to 9, 465 pounds and installation of wing spar reinforcement, modified tail wheel fork and truss assembly, metal covered control surfaces, and rectangular windows for installation on model AT-11, serial numbers 41-9486 and 6501.
FAA holder: Staggerwing Museum Foundation Inc.
SH1510SOLanding gear and brakes
Installation of external cargo rack and work platform between the skid gears. Limited to installation on serial number 911079D.
FAA holder: Haverfield Corporation
SA1158NWLanding gear and brakes
Installation of an auxiliary electric Hydraulic Pump System in accordance with Simuflight, Seattle Modification and Installation Procedure Instruction Report SS-900. NOTE: This system augments the existing manually operated hydraulic system for the landing gear and flap operation.
FAA holder: McHugh Aviation Inc
SA1244NWLanding gear and brakes
Installation of a machined wrought 2024-T351 tail wheel collar (Republic P/N 1126) in place of a die-forged 2014-T6 original part in accordance with Simuflight, Seattle Drawing Number SP-2000.
FAA holder: McHugh Aviation Inc
SA2925WELanding gear and brakes
Installation of power brake and skid control system.
FAA holder: W Morgan Hetrick
SA3373WELanding gear and brakes
Installation of Hydro-Aire power brake/skid control system.
FAA holder: W Morgan Hetrick
SA2262SWLanding gear and brakes
Modification of hydraulic brake system.
FAA holder: L-3 Communications Integrated Systems LP
SA02839ATLanding gear and brakes
Modification of the main landing gear bulkhead to improve static strength and fatigue characteristics.
FAA holder: Aircrafters of Enterprise Inc